-
MOR SE1 Balanced Mechanical Seal for Power Plant Sulzer PumpSize: 30 mm to 100 mm. Pressure: 0 ~ 1.5 MPa. linear velocity: 20 m/s. Temperature: -20°C to 120°C (250°F) (elastomer‑dependent).
-
MOR 48LP mechanical sealShaft Diameter: 20 mm – 120 mm (0.787” – 4.724”)Working Pressure: Up to 3.0 MPaWorking Temperature: -20 °C ~ +220 °C (dependent on elastomer material)Rotating Speed: Up to 3800 r/minTemperature:
-
MOR Stern Tube SealMOR Marine Stern Tube Air Seal for a marine stern tube air seal system, which is a critical part of the stern shaft sealing assembly for large oil-lubricated propeller shafts. It prevents seawater
-
MOR 122 Double Cartridge Mechanical SealPressure Range : 0~4 MPaTemperature Range : -60~260 °CLinear Speed : 0~7000 r/minShaft Diameter : 22~280 mm
-
MOR 5840 Cartridge Slurry SealShaft Diameter: 25 mm – 150 mm (0.984” – 5.906”)Working Pressure: Up to 4.0 MPaWorking Temperature: -30 °C ~ +250 °C (dependent on elastomer material)Rotating Speed: Up to 4200 r/minSeal Type:
-
MOR JCS2A Pharmaceutical Centrifugal Pump SealsSize: 30–120 mm (custom sizes available). Pressure: 0–2.5 MPa (process); up to 1.5 MPa (barrier fluid). linear velocity: ≤20m/s. Temperature: -20 °C to +180 °C (standard); -40 °C to +220 °C (special
-
MOR M481KL mechanical sealSize: 25 – 100 mm (custom sizes available). Pressure: ≤2.5mpa. linear velocity: ≤20m/s. Temperature: -20 °C to +220 °C (material‑dependent).
-
CURC glass lined reactor mechanical sealSize: 20 mm – 100 mm (custom sizes available). Pressure: ≤1.6MPA. linear velocity: ≤20m/s. Temperature: -20 °C to +180 °C (depends on elastomer material).
-
MOR LC900/1150II Mechanical Seal (For FGD Slurry Circulation Pumps)Size: Up to 250 mm (compatible with LC900/1150 pumps). Pressure: ≤1.6MPa. Temperature: ≤250℃. Speed≤ 15 m/s
-
MOR SE2-AP Double Cartridge Mechanical SealSize: 25 mm – 110 mm. Pressure: 0 ~ 2.5 MPa. linear velocity: 20 m/s. Temperature: -40°C to +220°C.
-
MOR CSSN cartridge type sealSize: 24 mm – 150 mm (1 – 6). Pressure: ≤ 2Mpa. Linear velocity: ≤ 20 m/s. Temperature: -40°C to +220°C (material‑dependent).
-
MOR 522 EKATO Single-Acting Mechancial SealSize: 40-220mm. Pressure: ≤4 MPa. linear velocity: ≤15 m/s. Temperature: - 50 ~ 400 ºC.
WebThe balance ratio (B) of a mechanical seal is given by the ratio of the hydraulically loaded area (Ah) and the sliding surface area (As): Balanced mechanical seals have a balance ratio B<1...
Webbellows mechanical seal 8648VRS. pump metal balanced. Operating pressure: 1,500 psi - 2,200 psi. Operating temperature: -20 °C - 204 °C. ... dual unpressurized arrangement, without outboard seals...
WebThe SAI™ is a short internal balanced mechanical seal for use with the AESSEAL ® SO5 seat. Non-shaft-fretting design to reduce cost of equipment overhaul. Maximizes seal life in suspensions and...
Webe) Balanced Seals: Balanced seals have higher-pressure limits, lower seal face loading, and generate less heat. Balancing a mechanical seal involves a simple design change, which reduces the...
WebThe seal shown in Figure 9 is said to be a “balanced” seal; its balance ratio is less than 100%. The balance ratio of “balanced” seals is typically from 65% to 90%. The distinction between...
WebApr 5, 2019 · Pumps are one of the largest users of mechanical seals. As the name suggests, mechanical seals are contact-type seals, differentiated from aerodynamic or labyrinth noncontact seals....
