-
![MOR 523 LIGHTNIN Spring Seal]()
MOR 523 LIGHTNIN Spring SealShaft size: 18–120 mm (standard)Pressure: ≤ 1.5 MPa (15 bar) / ≤ 3.0 MPa (30 bar)Temperature: 0–150 °C (standard) / −20–200 °C (high‑temp)Speed: ≤ 5 m/s (mixer) / ≤ 20 m/s (pump) -
![MOR T.587-D/8B1D-SP-D Cartridge Mechanical Seal]()
MOR T.587-D/8B1D-SP-D Cartridge Mechanical SealThe MOR T.587-D/8B1D-SP-D cassette mechanical seal features a single-sided double-balance design; it is a specially customized variant derived from the General Motors 587-SP series. Advantages This -
![MOR 286HT]()
MOR 286HTSize: 25 mm – 610 mm (1.0 – 24) or customized. Pressure: 0～2MPa. linear velocity: ≤20r/m. Temperature: -40°C to 400°C (-40°F to 750°F). -
![MOR 8BIVORS Single Mechanical Seal]()
MOR 8BIVORS Single Mechanical SealSize: 20 – 100 mm (Custom sizes available). Pressure: Vacuum to 1.6 MPa. linear velocity: ≤20m/s. Temperature: -20 ℃ to +250 ℃ (Metal bellows version up to 400 ℃). -
![MOR M481KL mechanical seal]()
MOR M481KL mechanical sealSize: 25 – 100 mm (custom sizes available). Pressure: ≤2.5mpa. linear velocity: ≤20m/s. Temperature: -20 °C to +220 °C (material‑dependent). -
![MOR 5610 Series Mechanical Seal]()
MOR 5610 Series Mechanical SealSize:25 mm – 100 mm (Custom sizes available). Temperature: -20 °C to +180 °C (depends on elastomer material). Pressure:≤1.6MPa. Liner Speed: ≤25m/s. -
![MOR CK267 double mechanical seal for reactor]()
MOR CK267 double mechanical seal for reactorMaterials: According to customer's demands. Size: 30 mm to 100 mm. Pressure: 0 ~ 40 bar. linear velocity: 20m/s. Temperature: - 20 ~ 250 C°. Mediums: oil & chemical industry. -
![MOR LC900/1150II Mechanical Seal (For FGD Slurry Circulation Pumps)]()
MOR LC900/1150II Mechanical Seal (For FGD Slurry Circulation Pumps)Size: Up to 250 mm (compatible with LC900/1150 pumps). Pressure: ≤1.6MPa. Temperature: ≤250℃. Speed≤ 15 m/s -
![MOR SAF High Pressure Mechanical Seal]()
MOR SAF High Pressure Mechanical SealSize: 25 mm – 120 mm. Pressure : up to 10.0 MPa (100 bar) or higher. Linear velocity: ≤25m/s. Temperature: - 40 ~ 250 ºC. -
![MOR JCS1A Mechanical Seals for Centrifugal Pumps]()
MOR JCS1A Mechanical Seals for Centrifugal PumpsSize: 20 mm – 110 mm. Pressure: ≤ 1.6Mpa. linear velocity: ≤20m/s. Temperature: -20°C to +180°C (depending on elastomer material). -
![MOR NLT-350/400AEF-300 Mechanical seal]()
MOR NLT-350/400AEF-300 Mechanical sealSize: 20-300mm. Pressure: ≤3.5MPa. Temperature: ≤280℃. Speed: ≤ 15 m/s. -
![MOR Cartex universal mechanical seal]()
MOR Cartex universal mechanical sealSize: 25–100 mm (1.0–4.0 in); custom sizes available. Pressure: ≤2.0MPa. linear velocity: ≤ 10 m/s (standard); up to 23 m/s for high‑speed variants. Temperature: -40°C to +220°C (-40°F to 428°F).
Elanor Young
Dianna Merrill
Priscilla Kuhl
Allie Gibson
Richard Kohn
Camille Crane
Spring seals also known as S-seals and all-in-one T-seals comprise of a high modulus elastomer and two integrated anti-extrusion springs. They are used to effectively seal applications that are...
Static Seal Features: Helical wound flat ribbon spring offers a moderate to high spring load for static and slow dynamic conditions. Static Seal designs are available in standard heel, extended heel,...
Nov 08, 2019 · A simple air cylinder has O-rings to seal in the air, and the O-ring exhibits spring-like qualities to ensure a good seal over a broad temperature range. Metal Springs Metal springs,...
The spring-energized seal, a U-cup lip seal made from specially-formulated polymers and reinforced by an energizing component, can be a valuable tool in the engineer’s problem-solving arsenal. While...
Both seal types are double acting, and will effectively seal applications that are subjected to: Teesele is capable of operating in a dynamic mode, whereas Springsele is recommended for static...
Provides moderate spring force versus deflection. Various spring loads to meet friction and sealing requirements. Cross-sections available are 1/16in up to 1/2in. Available to fit in all Industrial,...